Adam Sweet's Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
===== Using Magic SysReq Keys in an Emergency =====

From [[http://www.cyberciti.biz/tips/reboot-or-halt-linux-system-in-emergency.html]]

The Linux kernel includes magic system request keys. It was originally developed for kernel hackers, however you can use them to reboot or shutdown the machine safely (remember safe reboot/shutdown == flush filesystem buffers and unmount file system and then reboot so that data loss can be avoided).

This is quite useful when Linux based system is not available after boot or after a X server crashed ( svgalib program crashes) or no display on screen. Sysrq key combo forces the kernel to respond it regardless of whatever else it is doing, unless it is completely locked up (dead).

Using further extension to iptables called ipt_sysrq (new iptables target), which allows you to do the same as the magic sysrq key on a keyboard does, but over the network. So if your network server is not responding you can still reboot it. Please note that Magic SysRq support need to be compiled in your kernel. You need to say “yes” to ‘Magic SysRq key (CONFIG_MAGIC_SYSRQ)’ when configuring the kernel. I’m assuming that you have Magic SysRq key’ support is compiled in your kernel.
Enable sysrq keys

By default it is not enabled on many Linux distributions. Add or modify following line (as soon as new Linux system installed) /etc/sysctl.conf:
kernel.sysrq=1

Save and close the file and reboot system to take effect.

How do I use the magic SysRq keys in emergency?

You need to use following key combination in order to reboot/halt/sync file system etc:

ALT+SysRq+COMMAND-KEY

The ‘SysRq’ key is also known as the ‘Print Screen’ key. COMMAND-KEY can be any one of the following (all keys need to hit simultaneously) :

    * ‘r’ : Grab keyboard input in XLATE mode, so that only the terminal is using it.
    * ‘e’ : Send a SIGTERM to all processes, except for init.
    * ‘i’ : Send a SIGKILL to all processes, except for init.
    * ’s’ : Will attempt to sync all mounted filesystems.
    * ‘u’ : Will attempt to remount all mounted filesystems read-only.
    * ‘b’ : Will immediately reboot the system without syncing or unmounting your disks.
    * ‘o’ : Will shutdown your system off (if configured and supported).
    * ‘h’ : Show help, indeed this the one you need to remember.

So whey you need to tell your Linux computer to reboot or when your X server is crashed or you don’t see anything going across the screen then just press:

ALT+SysRQ+s : (Press and hold down ALT, then SysRQ (Print Screen) key and press ’s’) -Will try to sync all mounted system

ALT+SysRQ+r : (Press and hold down ALT, then SysRQ (Print Screen) key and press ‘r’) -Will reboot the system.

If you wish to shutdown the system instead of reboot then press following key combination:
ALT+SysRQ+o

Typically you will want:

ALT+SysRQ+reisub

with a pause between each command letter.

ipt_sysrq is a new iptables target that allows you to do the same as the magic sysrq key on a keyboard does, but over the network. Sometimes a remote server hangs and only responds to icmp echo request (ping). Every administrator of such machine is very unhappy because (s)he must go there and press the reset button. It takes a long time and it’s inconvenient. So use the Network Magic SysRq and you will be able to do more than just pressing a reset button. You can remotely sync disks, remount them read-only, then do a reboot. And everything comfortably and only in a few seconds. Please see Marek Zelem page to enableIP Tables network magic SysRq function.

For more information read official Documentation for sysrq.c version 1.15 stored in /usr/src/linux/Documentation/sysrq.txt and read man page of sysctl, sysctl.conf.
Adam Sweet's Wiki

User Tools

Site Tools

Page Tools
